3D Print Queue — LUDDAN SERVICES LLC

P-001

Tolerance Cube

First post-success print. 20mm reference cube with embedded print-ID boss and clearance hole test at 4 diameters.

28g · 22 × 22 × 22mm · calibration

P-002

Cal2 Arm

Parametric calibration arm for microscope positioning. Fixed-length reference bar, snap-fit into base.

12g · 60 × 20 × 8mm · PETG-rated

P-003

Cable Comb

8-slot cable organizer, 5mm pitch. Mounts via M3 screw or double-sided tape. Stack multiple for wide cable runs.

6g · 80 × 18 × 12mm · stackable

P-004

AMS Color Swatches

Calibration swatches for Bambu AMS slots — Black PLA, White PLA, Red PLA, Blue PLA. ID boss on top face.

4g ea · 40 × 40 × 4mm · color-ID

P-005

Modular Camera Arm System

4-piece snap-together arm: hub, two segments, end cap. Designed for Tapo/Ring clip mount adaptors. Confirmed 90° rigid lock.

38g assembled · 260mm span · modular

P-006

AC Drain Vac Adapter (v3)

v3 (latest — smooth bore)

Slip-fit coupler from standard 3/4" AC drain line to shop-vac hose. v3 — smooth bore, no barb, press fit verified.

18g · 65 × 40mm OD · watertight

P-007

P2S Calibration Pads

6-pad set covering all Bambu P2S axis directions (X±/Y±/Z±). Labeled by axis and direction. Confirmed ±0.05mm repeatability.

4g ea · 30 × 30 × 3mm · 6-pack

P-008

Canon Tripod Mount

M10 thread female to 1/4-20 male adapter. Fits Canon 90D hot-shoe mount. PLA with 100% infill crown.

22g · 35 × 35 × 24mm · 100% infill

P-009

P2S Purge Basket (v2)

v2 (latest)

Snap-on purge waste tray for Bambu P2S. v2 — wider lip, deeper basket, no-print gap eliminated.

31g · 90 × 50 × 30mm · snap-fit

P-010

Tapo C110 Fit Test

5-socket fit ladder for Tapo C110 base post diameters: 9.0 / 9.5 / 10.0 / 10.5 / 11.0mm. Confirmed 10.5mm.

3g · 60 × 25 × 10mm · test only

P-011

Column Base

Weighted base for modular camera column. 150mm square footprint, chamfered edges, center post socket.

145g · 150 × 150 × 18mm · gyroid

P-012

Column Foot

Foot cap with anti-skid pad recess for modular column system. Confirmed snap-fit on P-011 socket.

14g · 60 × 60 × 8mm · PETG

P-013

Column Segment

60mm-tall extension segment for the modular camera column. Slip-fit top and bottom. Stackable x∞.

38g · 45 × 45 × 60mm · 3-wall

P-014

Camera Arm

Articulating arm for column-mount camera rigs. Ball-and-socket joint, 15° max deflection, positive detent.

42g · 120 × 32 × 28mm · 4-wall

P-015

Camera Mount Head

1/4-20 camera screw boss integrated with column-arm interface. Fits Canon, GoPro, and Tapo mounts.

28g · 60 × 42 × 30mm · 100% infill boss

P-016

Sheet Holder

Wall-mount sheet holder for A4/Letter calibration printouts. Spring-clip top, slot-entry bottom.

55g · 230 × 30 × 20mm · wall-mount

P-017

Hex Fit Test

Tolerance ladder for hex driver bits: 5.0 / 5.5 / 6.0 / 6.5 / 7.0mm. Confirmed 6.5mm loose → 6.0mm tight.

8g · 80 × 30 × 12mm · test only

P-018

Filament Cutter Mount

Clip-on mount for flush-cut snips on Bambu P2S side rail. No-adhesive, positive lock on extrusion slot.

12g · 50 × 35 × 22mm · clip-fit

P-019

P2S Door Clips (pair)

Replacement door-latch clips for Bambu P2S. Two-piece: male latch + female socket. Drop-in replacement, no tools.

6g pair · 28 × 14 × 8mm · PLA

P-020

Scraper Holster

Magnetic holster for palette knife / bed scraper. Neodymium insert recess, mounts to Bambu P2S side panel.

18g · 80 × 30 × 15mm · magnet recess

P-022

Overhang / Bridge Test

Systematic overhang test at 30°/45°/60°/70°/80° plus three bridge lengths: 20/40/60mm. Results feed the support-strategy library.

22g · 90 × 50 × 30mm · test only

P-023

NACA 0015 Airfoil

Symmetric airfoil section at 1:1 scale, 150mm chord. Printed flat and upright for layer-line comparison. Reference for drone/UAV research.

34g · 150 × 28 × 4mm · aerospace

P-024

NACA 4412 Airfoil

Cambered lifting airfoil (4% camber, 12% thick), 150mm chord. Flat and upright variants. 12° stall angle confirmed in bench test.

36g · 150 × 26 × 6mm · aerospace

P-025

MegaTest Plate

Consolidated calibration block: overhang, bridge, peg-hole fit, text emboss, layer adhesion. All tolerances in one 20-min print.

48g · 100 × 80 × 25mm · calibration

P-026

Drone Arm Prototype

First drone-frame arm in 4-wall PLA. 200mm span, M3 motor-mount pattern, integrated wire chase. Break-test: 3.2kg before delamination.

61g · 200 × 28 × 14mm · 4-wall PLA

P-027

GPS Bracket

v20T (GPS bolt pattern confirmed)

Universal adapter plate for Garmin GPS-style units. Confirmed bolt pattern 79.4×52.0mm. Printed in Black PLA, 4 walls, gyroid infill.

107g · 106 × 106 × 38mm · watertight

P-028

GPS Top-Entry Cradle (V12)

V12 (latest)

Fully enclosed tray, GPS unit drops in from above with 45° guide chamfers. V12 — refined wall thickness, snap-lock tab added.

57g · 106 × 106 × 38mm · snap-fit

P-029

Print Storage Bin

220×180×140mm storage bin for completed prints. 3-wall sides, ribbed base, stacking lip. Printed in White PLA, ~11h.

269g · 220 × 180 × 140mm · 3-wall

P-030

Ebsary Phone Stand

3-color branded phone stand for client gift. LUDDAN logo on front face. Printed White+Red+Black via AMS.

61g · 90 × 70 × 127mm · 3-color AMS

P-031

Cable Comb v2

Redesigned cable comb: 10-slot, 4mm pitch, integrated zip-tie bosses. Replaces P-003 for tight-run applications.

8g · 90 × 20 × 14mm · v2